Page 1 of 1
Open cd drive as trigger
Posted: Wed May 04, 2016 4:46 pm
by Dimsok
I want to start program after inserting cd or dvd in drive. Did try file monitor as trigger or variables like {VolumeLabel(j:)} to start total commander with /S /O /L /T J:/. The same with E: for the first cd drive. Total commander open disc in new tab after inserting. But when i put out disc from drive trigger works again and tries to open empty drive. Is it possible to do some condition which will make action only after inserting disc in dvd drive, but not after putting it out?
Re: Open cd drive as trigger
Posted: Thu May 05, 2016 9:26 am
by Oleg
RoboTask contains such trigger.
Look at the
On Device Changed trigger
It is in "System Events" group
This trigger fired when you insert CD/DVD into optical drive or insert external storage into USB port (flash-drive or external HDD)
Re: Open cd drive as trigger
Posted: Thu May 05, 2016 4:44 pm
by SIS
what's the trigger when i connect a USB Drive?
i want that when i connect a certain USB drive it should run a task to copy a folder.
Thanks
Re: Open cd drive as trigger
Posted: Thu May 05, 2016 5:08 pm
by Oleg
what's the trigger when i connect a USB Drive?
Trigger the same:
On Device Changed
You can check disk label. For example your backup drive should have the label
MYBACKUP
Look at the example below
Code: Select all
;*****************************
;* RoboTask Task file
;* Do not edit in text editor!
;*****************************
[Root]
ActionAfterRun=INTEGER|0
Actions=FOLDER
Automat=INTEGER|-1
CatID=INTEGER|1657389313
Comment=STRINGLIST
ContinueOnError=INTEGER|0
Events=FOLDER
ExternalName=STRING|"Task219"
Hide=INTEGER|0
ID=INTEGER|561213642
LogOnAsUser=INTEGER|1
Name=STRING|"Check USB drive"
OnErrorTaskID=INTEGER|-1
Priority=INTEGER|3
RunOnClose=INTEGER|0
RunOnStartup=INTEGER|0
ToLog=INTEGER|3
UnicodeFormat=INTEGER|1
WriteGeneralLog=INTEGER|0
[Actions]
Action1=FOLDER
Action2=FOLDER
Action3=FOLDER
Action4=FOLDER
Action5=FOLDER
Action6=FOLDER
[Actions\Action1]
ActionID=STRING|"A_DIALOG_MESSAGE"
Enabled=INTEGER|0
Name=STRING|"Show ""{dsk}"""
Params=FOLDER
[Actions\Action1\Params]
icon=STRING|"1"
msg0=STRING|"{dsk}"
msg1=STRING|"{VolumeLabel({dsk}:\)}"
msgcount=STRING|"2"
playsound=STRING|"0"
showmessage=STRING|"1"
[Actions\Action2]
ActionID=STRING|"A_FLOW_IF"
Enabled=INTEGER|-1
Name=STRING|"If Then"
Params=FOLDER
[Actions\Action2\Params]
case=STRING|"0"
connection=STRING|"0"
count=STRING|"1"
operator=STRING|"0"
type=STRING|"0"
value1=STRING|"{VolumeLabel({dsk}:\)}"
value2=STRING|"mybackup"
[Actions\Action3]
ActionID=STRING|"A_DIALOG_MESSAGE"
Enabled=INTEGER|-1
Name=STRING|"Show ""Disk {dsk}: inserved"""
Params=FOLDER
[Actions\Action3\Params]
icon=STRING|"1"
msg0=STRING|"Disk {dsk}: inserved"
msg1=STRING|"It is my backup drive."
msg2=STRING|"You can put here synchronization of your working folders"
msgcount=STRING|"3"
playsound=STRING|"0"
showmessage=STRING|"1"
[Actions\Action4]
ActionID=STRING|"A_FLOW_ELSE"
Enabled=INTEGER|-1
Name=STRING|"Else"
[Actions\Action5]
ActionID=STRING|"A_DIALOG_MESSAGE"
Enabled=INTEGER|-1
Name=STRING|"Show ""Disk {dsk}: inserved"""
Params=FOLDER
[Actions\Action5\Params]
icon=STRING|"0"
msg0=STRING|"Disk {dsk}: inserved"
msg1=STRING|"It is NOT my backup drive."
msgcount=STRING|"2"
playsound=STRING|"0"
showmessage=STRING|"1"
[Actions\Action6]
ActionID=STRING|"A_FLOW_ENDIF"
Enabled=INTEGER|-1
Name=STRING|"End If"
[Events]
Event1=FOLDER
[Events\Event1]
Enabled=INTEGER|-1
EventID=STRING|"E_SYSEVENTS_DEVICECHANGE"
Params=FOLDER
UnigueID=INTEGER|16445697
[Events\Event1\Params]
assign=STRING|"0"
changekind=STRING|"1"
devicekind=STRING|"1"
parameter=STRING|"dsk"
useparameter=STRING|"1"
Save the text of the task to a file and use menu Task->Import to import the task into RoboTask.
Do not forget to enable the task after importing.